Difference between revisions of "Ender-3 S1"
(→Printer Features) |
|||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| − | The Ender-3 S1 was procured by a member faction interested in increasing project [https://en.wikipedia.org/wiki/Flux#Flux_as_flow_rate_per_unit_area flux] within the Digital Fabrication Lab at Bloominglabs. By upgrading our equipment (as measured according to the metric of Low Cognitive and Maintenance Overhead to Use, rather than performance ''simpliciter''), it is hoped that more investment of attention and resources will be drawn to this sector of the space. | + | The Ender-3 S1 was procured by a member faction interested in increasing project [https://en.wikipedia.org/wiki/Flux#Flux_as_flow_rate_per_unit_area flux] within the Digital Fabrication Lab at Bloominglabs. |
| + | |||
| + | By upgrading our equipment (as measured according to the metric of Low Cognitive and Maintenance Overhead to Use, rather than performance ''simpliciter''), it is hoped that more investment of attention and resources will be drawn to this sector of the space. | ||
OEM product listing: https://www.creality.com/products/creality-ender-3-s1-3d-printer | OEM product listing: https://www.creality.com/products/creality-ender-3-s1-3d-printer | ||
| + | |||
| + | [[Image:Ender3_20240109_160554.jpg|none|thumb|300px|Ender 3-S1]] | ||
== Printer Features == | == Printer Features == | ||
| Line 7: | Line 11: | ||
220x220x270 mm build volume | 220x220x270 mm build volume | ||
| − | Single nozzle extruder, max temp 260 C | + | Single nozzle extruder, 0.4 mm diameter, max temp 260 C |
Heated build platform, max temp 110 C, with removable magnetic surface sheet | Heated build platform, max temp 110 C, with removable magnetic surface sheet | ||
| Line 15: | Line 19: | ||
See "Product Parameters" on the OEM page above for further information. | See "Product Parameters" on the OEM page above for further information. | ||
| − | Mechanical bed depth sensor: used by the printer to construct a map of variations in the build platform. Note that this printer does not auto-level: the z-offset, and build platform tensioning wheels, must be set manually. Full procedure available on the Creality FAQ page for the Ender-3 S1 (not Pro or Plus): https://www.creality.com/pages/faq | + | Mechanical bed depth sensor: used by the printer to construct a map of variations in the build platform. |
| + | |||
| + | Note that this printer does not auto-level: the z-offset, and build platform tensioning wheels, must be set manually. Full procedure available on the Creality FAQ page for the Ender-3 S1 (not Pro or Plus): https://www.creality.com/pages/faq | ||
| + | |||
| + | == Usage Information == | ||
| + | |||
| + | Please note any changes in printer functionality or settings (z-offset, manual re-levelling, firmware modification, cleaning, repairs, mechanical/electrical/software failures, etc.) in the Log below. | ||
| + | |||
| + | Please route all filament through the filament sensor, to avoid partial prints. | ||
| + | |||
| + | Known good filament: | ||
| + | 1.75 mm diameter | ||
| + | PLA, ABS, TPU, PETG | ||
== Log == | == Log == | ||
| − | [Please include status | + | [Please include a status report at the top of all Log entries.] |
20240109: | 20240109: | ||
| Line 25: | Line 41: | ||
Status: Functional | Status: Functional | ||
| − | Printer assembled, bed leveled, z-offset set to -3. | + | Printer assembled, bed leveled, z-offset set to -3.15 mm, first test print. |
| + | |||
| + | [[Category:3D Printers]] [[Category:Tools]] | ||
Latest revision as of 13:26, 10 January 2024
The Ender-3 S1 was procured by a member faction interested in increasing project flux within the Digital Fabrication Lab at Bloominglabs.
By upgrading our equipment (as measured according to the metric of Low Cognitive and Maintenance Overhead to Use, rather than performance simpliciter), it is hoped that more investment of attention and resources will be drawn to this sector of the space.
OEM product listing: https://www.creality.com/products/creality-ender-3-s1-3d-printer
[edit] Printer Features
220x220x270 mm build volume
Single nozzle extruder, 0.4 mm diameter, max temp 260 C
Heated build platform, max temp 110 C, with removable magnetic surface sheet
Filament sensor.
See "Product Parameters" on the OEM page above for further information.
Mechanical bed depth sensor: used by the printer to construct a map of variations in the build platform.
Note that this printer does not auto-level: the z-offset, and build platform tensioning wheels, must be set manually. Full procedure available on the Creality FAQ page for the Ender-3 S1 (not Pro or Plus): https://www.creality.com/pages/faq
[edit] Usage Information
Please note any changes in printer functionality or settings (z-offset, manual re-levelling, firmware modification, cleaning, repairs, mechanical/electrical/software failures, etc.) in the Log below.
Please route all filament through the filament sensor, to avoid partial prints.
Known good filament: 1.75 mm diameter PLA, ABS, TPU, PETG
[edit] Log
[Please include a status report at the top of all Log entries.]
20240109:
Status: Functional
Printer assembled, bed leveled, z-offset set to -3.15 mm, first test print.
